How to Hang Pictures on Brick and Concrete: 5 Ways Compared

in
Lee Orlian, interior designer and co-founder of Teepee Joy

Written by

Lee Orlian

Interior designer and co-founder of Teepee Joy.

Updated November 20, 2026

To hang pictures on brick without drilling, use brick clips on exposed brick, which their makers rate up to 30 pounds. For anything heavy or over a bed, drill a masonry anchor, and set it in the brick rather than the mortar.

That last part surprises people because the usual advice is to drill the mortar. It works for a light frame, and below is where I draw the line.

Old brick is one of my favorite backdrops for kids' art, and this post covers only what changes on brick and concrete.

For strips and rails on an ordinary wall, see my How to hang pictures without nails post, and for the measuring, my How to hang a picture post.

Jump to a section:

Can you hang pictures on brick without drilling?

Yes, on a wall with deep joints. Clips need the mortar set back from the face, and Picture Hang Solutions asks for at least a quarter inch of each brick standing out past the joint (Picture Hang Solutions).

Push the end of a tape measure into a joint and read it.

If the joints sit level with the face, or thick paint has filled them, a clip has nothing to grip. Command doesn't recommend its strips on brick either, so on a flat wall like that you're choosing between a drill and a different wall.

5 ways to hang pictures on brick, compared

Here's the short version, with the limits I could find on each maker's own page.

Way Holes Maker's limit Over a crib or bed
Brick clips None Up to 30 pounds Never
Adhesive strips and hooks None Not recommended on brick Never
Rail or ledge fixed once A few, once Depends on the product No
Anchor in the mortar Small, easy to patch None published that I could find No
Anchor in the brick Small, harder to hide Depends on the anchor Yes, with plexi

Brick clips

Think of a small clamp with a hook on it. Hangman's Brick Hooks fit bricks 2¼ to 2¾ inches tall and support up to 30 pounds (Hangman).

Picture Hang Solutions also lists 30 pounds and says to use two for heavier items. Measure one brick and weigh your frame before you buy.

The catch is height. A clip can only sit where a brick is, so the frame lands a little above or below your mark. On a play wall, nobody will notice.

My rule for kids' rooms: clips are fine on a playroom wall, never over a bed. A clip holds by gripping, and over a sleeping child I want something fixed into the wall.

Best for: a playroom wall, a hallway, a rental.

Sepia and soft color sit well against red brick: vintage airplanes, small animals at the wheel of old racing cars, or a carnival in coral and teal.

Shop this artBrick clips: vintage airplanes in soft sepia print
Vintage airplanes in soft sepia
Shop this artBrick clips: animals driving vintage racing cars print
Animals driving vintage racing cars
Shop this artBrick clips: carnival rides and toys in coral and teal print
Carnival rides and toys in coral and teal

Adhesive strips and hooks

Rough surfaces are where these fail. Command says its products are "not recommended for wallpaper, brick, or rough concrete" (Command FAQ). Its Canadian FAQ is blunter: no, and the Outdoor line isn't for brick either (Command Canada).

Framebridge says strips may hold lightweight art on smoother painted brick (Framebridge), but I wouldn't. Command's instructions say not to hang over beds (Command how-to).

Best for: on bare brick, nothing.

A picture rail or a ledge fixed once

A few holes once, then you can change the art for years. STAS rates its cliprail at 20 kg per meter, about 44 pounds (STAS). IKEA lists 11.02 pounds for the shorter MOSSLANDA ledge and leaves the fasteners to you, because different walls need different ones (IKEA).

On masonry, those fasteners are anchors. A rail or ledge carries every frame on it, so I treat it as heavy and fix it into the brick, not the mortar.

Best for: a playroom where the art keeps changing.

A rail suits a set you'll add to. Pencil Sketch Animals has 20 designs and Sepia Meadow Dogs has 12, and Cowboy Hat Dogs brings bright colored-pencil-style pups for a wall that needs waking up.

Shop this artA picture rail or a ledge fixed once: woodland and safari animals in pencil-sketch style print
Woodland and safari animals in pencil-sketch style
Shop this artA picture rail or a ledge fixed once: dogs in a sepia watercolor style print
Dogs in a sepia watercolor style
Shop this artA picture rail or a ledge fixed once: dogs in western wear, in bright colors print
Dogs in western wear, in bright colors

Masonry anchors in the mortar

Most hanging guides send you here first. Pine Hall Brick, which makes brick, uses the joint for decor, mirrors and shelving because mortar is softer, easier to drill and simple to repair (Pine Hall Brick).

Framebridge drills about an inch into mortar to avoid cracking the brick face (Framebridge).

This Old House disagrees. It says to drill the brick unless you're hanging something under two pounds, because mortar can't hold much and wears out faster (This Old House).

You won't find a holding number here, on purpose. Hilti's data sheet for its HUS 6 screw anchor says there is no test data for loads in mortar joints (Hilti), and I found no maker publishing one.

My call: mortar is for small, light frames on a wall nobody sleeps under.

Best for: one light frame on a play wall, or a rental where your landlord has said yes.

Small singles belong here. A fox in a flat cap strides off with his golf clubs, with a brown and cream striped border that matches our Striped Sepia Western set.

Shop this artMasonry anchors in the mortar: a fox in a flat cap with his golf clubs print
A fox in a flat cap with his golf clubs
Shop this artMasonry anchors in the mortar: western animals inside brown and cream stripes print
Western animals inside brown and cream stripes
Shop this artMasonry anchors in the mortar: a sloth in a rusty vintage truck print
A sloth in a rusty vintage truck

Masonry anchors in the brick

Heavy frames go here. This Old House suggests plastic anchors made for masonry under 10 pounds, and expansion bolts or sleeve anchors above that (This Old House).

Screw anchors like Tapcon cut their own threads into concrete, brick or block (ITW Red Head).

Hilti recommends 0.2 kN of pull-out for one HUS 6 in solid brick, about 45 pounds, and 0.3 to 0.4 kN of shear, about 67 to 90 pounds. That's one anchor in one kind of brick, so go by your own pack. The hook has a limit too.

Best for: big frames, a rail or ledge, and anything over a crib or bed.

Blue is my favorite trick on red brick, because it sits opposite orange on the color wheel and most red brick leans orange.

Six 16x24 prints in two rows of three, with 2 inches between them, make a block about 52 inches wide and 50 inches tall. That's a lot of frame, so weigh it and drill for it.

Shop this artMasonry anchors in the brick: farm horses in deep blue and cream print
Farm horses in deep blue and cream
Shop this artMasonry anchors in the brick: horses against sky blue, in a textured oil-painting style print
Horses against sky blue, in a textured oil-painting style
Shop this artMasonry anchors in the brick: horses under pink skies and misty blue peaks print
Horses under pink skies and misty blue peaks

How do you drill into brick safely?

Eye and lung protection come before the first hole.

  1. Protect yourself. This Old House lists a dust mask, safety glasses, earplugs and work gloves, and warns that cutting brick, mortar or concrete makes a very fine crystalline silica dust you don't want to breathe (This Old House). Tapcon's maker says to wear safety glasses with side shields (ITW Red Head). Keep children out of the room until the floor is clean.
  2. Look at the mortar first. Crumbly mortar is no place for an anchor, so if it scratches away, go to the brick. In brick, This Old House says to stay more than an inch from any edge, or it can split.
  3. Use the right bit. Get a carbide-tipped masonry bit in the size your anchor calls for. Tapcon pairs a 5/32-inch bit with its 3/16-inch anchor and warns that the wrong size may cause failure. A hammer drill is the usual tool, but check your anchor's sheet, since Hilti's HUS 6 wants brick drilled without the hammer action.
  4. Mark the depth. Tapcon wants the hole at least 1/4 inch deeper than the anchor goes. Wrap painter's tape around the bit so you know when to stop.
  5. Drill slowly and straight. This Old House eases the bit back every 10 seconds or so to clear dust. If you feel sudden resistance or hear a metallic sound, stop and move over.
  6. Vacuum the hole and the floor. Dust left in the hole can block the anchor.
  7. Set the anchor gently. Hilti warns that over-tightening in soft material leaves the fixing unusable.

Painted brick in a home built before 1978 needs one more check: EPA says homes that age may have lead-based paint, so read its advice before you drill (EPA).

How do you hang pictures on concrete walls?

Plan on a drill, nearly always. Clips need a brick to clamp onto, and Command rules out rough concrete. Its Canadian FAQ does say its products stick to painted, smooth cinder block, so check the pack if your basement playroom has that kind of wall.

On poured concrete there's no mortar question, so the anchor goes where the frame needs it.

ITW lists one 3/16-inch Tapcon set 1 inch deep in 2,000 psi concrete at an ultimate 600 pounds of pull-out and 720 of shear, and says a safe working load should not exceed 25 percent of that: 150 and 180 pounds.

In lightweight hollow block it drops to 55 and 100 pounds at 25 percent (ITW Red Head). That sheet dates from 2012, so trust your pack.

If you hit metal, This Old House says to stop and move over, and to call a professional if it keeps happening.

Keep the hole only as deep as the anchor needs, since wires or pipes can sit behind a wall (Framebridge). In a concrete apartment building, ask the building first.

Gray concrete is cool and flat, so I want warmth or contrast: terracotta hills with small black riders, or a black and white close-up of an astronaut's visor reflecting the moon.

Shop this artRiders on terracotta hills print
Riders on terracotta hills
Shop this artTwo riders on a ridge in brushstroke style print
Two riders on a ridge in brushstroke style
Shop this artThe moon reflected in an astronaut's visor print
The moon reflected in an astronaut's visor
Shop this artJets and propeller planes in pencil-sketch style print
Jets and propeller planes in pencil-sketch style

Brick and concrete in a kids' room

In a child's room, I center wall art about 48 inches from the floor, and it can stay there as they grow. The 57 inches you'll often read is meant for grown-up rooms, where people stand (Architectural Digest). My how high to hang pictures post has the full picture.

Over a crib or a toddler bed, hang it securely with proper hardware, never tape or one small nail, and choose the framed version with kid-safe plexi, not glass. On brick or concrete, proper hardware means a drilled anchor.

Clips and strips stay off that wall, and I use two anchors even for a single frame, so it isn't relying on one point. Keep the crib itself empty except for a fitted sheet (NIH Safe to Sleep).

Renting? Drilled holes in mortar can be patched, but check first: ask your landlord and read your lease before you drill anything.

Clips are the easier yes, since Hangman says they come off without permanent marks or holes. If you can't drill, leave the wall over the bed bare and hang the art somewhere else.

Busy brick wants a plain partner. Art on a quiet cream ground holds its own, and a walnut or black frame gives it an edge where natural oak can melt into orange brick.

Our frames come in natural oak, walnut, white and black, with kid-safe plexi or real glass, and they arrive with hanging hardware (our FAQ). My gallery wall layouts post has measured layouts for bigger groups.

For the wall over a bed, I'd look at Soft Sepia Cats in warm cream, or Olive Gingham Vintage Western. Two wide singles also work, and both are best sellers: a little astronaut holding a jar of stardust, and a bear cub reaching for falling leaves.

Shop this artCats in soft sepia and cream print
Cats in soft sepia and cream
Shop this artWestern designs in sepia and olive gingham print
Western designs in sepia and olive gingham
Shop this artA little astronaut with a jar of stardust print
A little astronaut with a jar of stardust
Shop this artA bear cub reaching for falling leaves print
A bear cub reaching for falling leaves
Shop this artA cowboy hat under the words Long Live Boyhood print
A cowboy hat under the words Long Live Boyhood

Hanging pictures on brick: questions parents ask

Is it better to drill into brick or mortar?

Each has a job. Mortar is easier to drill and patch but weaker, so I use it for a small frame on a play wall and brick for everything else.

Do adhesive strips stick to brick?

Don't count on them. Command doesn't recommend its products on brick or rough concrete (Command FAQ).

What do brick clips hold?

Up to 30 pounds, on both listings I read (Hangman, Picture Hang Solutions), as long as your joints are deep enough to grip.

Can you hang pictures on a brick fireplace?

Yes. Hangman lists fireplaces among its uses, and clips are where I'd start, since nothing goes into the chimney. If it's a working fireplace, ask a mason or chimney sweep before you drill.

How do you remove anchors from mortar?

Tapcon and Hilti both list their screw types as removable, so a driver backs them out (Tapcon flyer, Hilti).

For a plastic sleeve, take out the screw, grip the collar with needle-nose pliers and pull slowly. HomeServe describes that for drywall (HomeServe), and I'd stop if the mortar starts to crumble.

To patch the hole, brush out loose bits, mist it, pack in fresh mortar and shape it to match (Hunker). A mortar-patch caulk is the quick option (Sherwin-Williams).

Shop art for a brick wall

Start with our kids' wall art or our boys' wall art. For a whole wall, browse our gallery wall sets: every set in this post goes up to four prints and most go to six, all in one size.

There's more in our playroom wall art, horse wall art sets and western wall art sets.

Check the joints, weigh the frame, then pick the way that suits the wall.